Telefon:06209238719, 06309408330
E-mail:[email protected]

Electrolux mosogató

Type of alarm

No. flashes of end-of- cycle LED and “beeps”

Displayed to the user

Description of the alarm condition

Machine status

Possible causes

i10

1

YES

Water fill time-out

(The pressure switch does not close on FULL after 90 sec. static fill, or never

closes on “FULL” during the initial 60

sec of the dynamic fill at 2800 rpm)

The drain pump switches on, then the cycle stops

Tap closed; water mains pressure too low; fill solenoid / wiring faulty; hydraulic circuit of pressure switch obstructed; level pressure switch / wiring faulty; circuit board faulty (solenoid triac short- circuited)

i20

2

YES

Water drain time-out

(The pressure switch does not return to EMPTY after two drain phases lasting 120 seconds) (**)

The drain pump switches on, then the cycle stops

Drain circuit obstructed/blocked; drain pump interrupted or jammed (foreign bodies); level

pressure switch blocked on FULL (1-3); hydraulic circuit of pressure switch obstructed; wiring faulty;

circuit board faulty

i30

3

YES

Intervention of Anti-flooding system

(the drain pump switches on)

The cycle is interrupted and the drain pump switches on

Water leakage from the tub – sump and various

connections (pump, upper spray arm duct etc.); floating sensor blocked mechanically; microswitch faulty; fill solenoid blocked mechanically; circuit board faulty (solenoid triac short-circuited); wiring faulty

i50

5

YES

Motor triac short-circuited

(the washing pump runs uncontrolled at maximum speed)

Water fill to level (if necessary), disactivation of the other

actuators, cycle interrupted. The washing motor runs at maximum

speed and the alarm is displayed.

Circuit board faulty

(**) If inside the appliance there is no water at all (correct drain) but this alarm is displayed, check the heater (possible dispersion) and the anti-interference suppressor.

Type of alarm

No. flashes of end-of- cycle LED

and “beeps”

Displayed to the user

Description of the alarm condition

Machine status

Possible causes

i60

6

NO

Heating Time-out

(the check takes place every 3 minutes: the temperature must increase by a certain amount at each step)

The programme continues to the end without heating (the washing result will probably be unsatisfactory)

Heating element faulty; intervention of safety thermostats (open); wiring faulty; NTC sensor (poor thermal contact); insufficient water circulating in the tub; washing pump faulty (impeller stripped); circuit board faulty.

i70

7

NO

NTC sensor short-circuited or open

The programme continues to the

end without heating (the washing result will probably be unsatisfactory)

NTC sensor faulty; wiring short-circuited / open; circuit board faulty.

i80

8

NO

Communication error between the microprocessor and the EEPROM

Machine inoperative: no selection

possible (*)

Circuit board faulty.

i90

9

NO

Problems with software configuration

The fault occurs when switching on: no selection possible (*)

Circuit board faulty (configuration software incorrect).

ib0

11

NO

Problems with the turbidity meter

[if featured] (Calibration Time-out)

The programme continues as if a

“heavy soiling” condition had been detected.

Turbidity sensor faulty; sensor wiring faulty; circuit board faulty.

id0

13

NO

Problems with the washing motor: no signal from the tachymetric generator (washing pump powered, but no signal from the generator)

The heating element is switched off. If the fault persists after the

Time-out, the washing pump operates at maximum speed and

the alarm code is stored in memory (the cycle continues)

Motor winding interrupted / short-circuited; motor jammed (foreign bodies); wiring to washing motor faulty; motor capacitor faulty; Tachymetric generator interrupted / short-circuited; circuit board faulty.

iF0

15

NO

Water replenishment Time-out

(3 times during the T.S. Time-out)

The cycle continues until the next phase without supplementary fills

and without heating. The error is cancelled on completion of a drain

phase.

Dishes upside-down; central filter clogged; excessive foam; leaks from the sump-pressure switch coupling; pressure switch faulty / false contacts.

Electrolux mosogató
Értékelje a cikket!