6. Error Display
MESSAGE | ERROR | CAUSE | SOLUTION |
IE | WATER INlET ERRoR | The water tap is closed. | Open the water tap. |
The filter of the valve inlet is clogged. | Clean the filter of the valve inlet. | ||
The valve inlet is an inferior product or broke down. | Change the valve inlet. | ||
The water level sensor (sensor pressure) is an inferior product or broke down. | Change the water level sensor (sensor pressure). | ||
The drain motor works during water supply. | Change the drain motor. | ||
The PCB ASS’Y does not check the water level. | Change the pCb ASS’y. | ||
oE | DRAIN ERRoR | The drain hose is kinked or clogged. | Clean and straighten the drain hose. |
The drain motor is an inferior product. | Change the drain motor. | ||
The valve inlet works during drain. | Change the valve inlet | ||
The water level sensor is an inferior product . | Change the water level sensor. | ||
The PCB ASS’Y does not check the water level. | Change the pCb ASS’y. | ||
UE | UN-BALANCE ERRoR | The laundry is concentrated to one side of the drum during spin. | Rearrange the laundry. |
lE | DooR opEN ERRoR | The Start/Hold button is pressed while the door is opened. | Close the door. |
The switch door lock is an inferior product. | Change the switch door lock. | ||
The PCB ASS’Y does not check the door lock. | Change the pCb ASS’y. | ||
E1 | Water level detection error | Water level is below reset or overflow is detected | Change the sensor pressure. |
E2 | oVER floW ERRoR | The water is supplied continuously due to an inferior valve inlet. | Change the valve inlet. |
The valve inlet is normal, but the water level sensor (sensor pressure) is inferior. | Change the water level sensor (sensor pressure). | ||
The drain motor dose not work. (The fan motor is an inferior product or broke down.) | Change the drain motor. | ||
E3 | fAN MoToR ERRoR | The fan motor does not work. (The fan motor is an inferior product or broke down.) | Change the fan motor. |
The PCB ASS’Y does not control the fan motor. | Check the connector or change the pCb ASS’y . | ||
E4 | lEAKAGE ERRoR | Water leaks from the tub or the hose drain. | Check the leak of the tub or the hose drain. Then change the tub or the hose drain. |
The foreign matter is jammed in the drain bellows. (Non-pump model) | Remove the foreign matter in the drain bellows. | ||
E5 | HIGH VolTAGE ERRoR | The laundry is jammed between the gasket and the drum. | Rearrange the laundry. |
The PCB ASS’Y is an inferior product. | Change the pCb ASS’y. | ||
E6 | EMG ERRoR | The laundry is jammed between the gasket and the drum. | Rearrange the laundry. |
The motor is an inferior product. | Change the motor. | ||
The PCB ASS’Y is an inferior product. | Change the pCb ASS’y. |
MESSAGE | ERROR | CAUSE | SOLUTION |
E7 | DIRECTIoN | The motor spins into an opposite direction. | Change the PCB ASS’Y or the motor. |
The motor hall IC is an inferior product or broke down. | Change the motor hall IC or the motor. | ||
E8 | MoToR ERRoR | The motor is not normally connected. | Check the connector of the motor. |
The motor does not work. (The motor is an inferior product or broke down.) | Change the motor. | ||
E9 | SENSoR pRESSURE ERRoR | The water level sensor is an inferior product. | Change the water level sensor. |
H1 | THERMISToR (TEMp. SENSoR) DRy ERRoR | The thermistor dry is an inferior product or broke down. | Change the thermistor dry. |
The thermistor dry is not connected normally. | Check the connector of the thermistor dry. | ||
H2 | THERMISToR WASH ERRoR | The thermistor wash is an inferior product or broke down. | Change the thermistor wash. |
The thermistor wash is not connected normally. | Check the connector of the thermistor wash. | ||
H3 | THERMISToR DRy oVERHEATING ERRoR | The fan motor does not spin with the proper rpm. (The fan motor is an inferior product or broke down.) | Change the fan motor. |
The thermistor dry is an inferior product or broke down. | Change the thermistor dry. | ||
H4 | THERMISToR WASH oVERHEATING ERRoR | The heater worked without the water in the tub. | Check the water level. |
The thermistor wash is an inferior product or broke down. | Change the thermistor wash. | ||
H5 | WATER TEMp. ERRoR | The water temp. is over 45°C in delicate & wool course. | Change the thermistor wash. |
H6 | HEATER WASH ERRoR | The heater wash dose not work. (The water temp. doesn't rise over 2°C during 15min.) | Change the heater wash. |
H7 | HEATER DRy ERRoR | The heater dry dose not work. (The water temp. doesn't rise over 3°C during 8min.) | Change the heater dry. |
H8 | HEATER WASH oVERHEATING ERRoR | The heater worked without the water in the tub. | Check the water level and the heater wash. |
pfE | pUMp fIlTER ERRoR | The drain pump filter is clogged. | Clean the drain pump filter. |
The drain pump does not work during spin. | Change the drain pump. | ||
The large amount of detergent was used. | Use the proper amount of detergent. | ||
The drain hose is placed higher than 1m above the floor. | Place the drain hose 1m below the floor |