Hotpoint Washing Machines and Washer Dryers
- F10 – No cold fill. Check that the taps are on or if the drain hoses are kinked.
- F11 – No hot fill.The ambient temperature is likely to be below freezing possibly due to the pipes being frozen. Also check that the taps are on or if the drain hoses are kinked.
- F12 – No mixed fill. It is likely that the water is not turned on at the taps.
- F13 – Check the water supply, inlet valve and hot and cold hose connections.
- F14 – A fault with the water heating has occurred.
- F15 – Water is not being pumped out and a flood condition could occur. Check that the drainage hose is raised to the recommended minimum height and that the pipe is not blocked.
- F16 – Extremely high water level Disconnect or turn off the water supply and ensure that the water level does not rise any more. Then
- F17 – Door not closed properly. Close door firmly at the 3 o’clock position.
- F20/1 – The thermistor resistance has drifted or the temperature scanning sequence is incorrect. The ambient temperature could be below freezing. .
- F30/31 – A motor drive problem has occurred. Try running the programme again. If the problem persists .
- F40 – Water below protection level during a heat step.
- F41 – Water level detect sequence incorrect.
- F50/51 – Customer language and wash programme have not been saved. The system will run with default conditions (1000rpm max and English language). to re-programme your product.
Fault codes for Hotpoint LCD EVO1 Washing Machines and Washer Dryers
- F01 – Short circuit motor triac –
- F02 – Motor jammed tacho detached –
- F03 – Wash thermistor open/short circuit –
- F04 – Pressure switch jammed on empty –
- F05 – Pressure switch jammed on full –
- F06 – Program selector error –
- F07 – Heater relay stuck –
- F08 – Heater relay cannot be activated –
- F09 – Incompatible eeprom –
- F10 – Pressure switch not sensing correctly –
- F11 – Pump cannot be activated –
- F12 – Communication error –
- F13 – Dryer fan or dryer thermisotor faulty –
- F14 – Dryer element faulty –
- F15 – Dryer element relay faulty –
- H20 – Not filling. Check tap, hose and inlet valves
- LOCKED – Check interlock –
Fault codes for Hotpoint LCD EVO2 and V4 Washing Machines and Washer Dryers
- F01 – Motor traic short circuit –
- F02 – Motor jammed or tacho detached –
- F03 – Wash thermistor open/short circuit –
- F04 – Pressure switch jammed on empty –
- F05 – Pressure switch jammed on full – Check pump for blackages.
- F07 – Heater relay stuck –
- F08 – Heater relay stuck –
- F09 – Setup error –
- F10 – Pressure switch not sensing –
- F11 – Pump cannot be activated – .
- F12 – No communication between cards –
- F13 – Drying thermistor open/short circuit – Book an appliance repair.
- F14 – Drying element faulty – Book an appliance repair.
- F15 – Dryer element relay fault – Book an appliance repair.
- F17 – Interlock error – Book a washing machine repair.
- F18 – Communication error – Book a washing machine repair .
- H20 – Not filling. Check tap, hose and inlet valves
Hotpoint Fridges and Freezers
- F1 – Freezer thermistor open circuit. Book a freezer repair .
- F2 – Freezer thermistor short circuit. Book a freezer repair.
- F3 – Fridge thermistor open circuit. Book a fridge repair.
- F4 – Fridge thermistor short circuit. Book a fridge repair.
- F7 – Evaporator thermistor open circuit. Book a fridge repair .
- F8 – Evaporator thermistor short circuit. Book a fridge repair.
- F9 – Temperature set switch open circuit Book a fridge repair.
- FA – No feedback from Baffle Book a fridge repair.
- FB – Fridge Baffle motor operating continuously. Book a fridge repair.
- FE – Defrost time out. Book a freezer repair.
You can also buy spare parts for your fridge or freezer at the Hotpoint Refrigeration Spare Parts shop
Hotpoint Dishwashers
- F10 – Fill or empty time out. Check that the hoses are not kinked, that the taps are on or whether the drain pump or the hose is blocked.
- F11 – Heater timed out. The heater has not reached the required level. Book a dishwasher repair.
- F20 – Temperature under range. Book a dishwasher repair. .
- F21 – Temperature over range.Book a dishwasher repair.
Fault codes for Hotpoint LCD Dishwasher Models
- A01 – Float switch operated – Book a dishwasher repair.
- A02 – Open/Short circuit heater relay – Book a dishwasher repair.
- A03 – Short circuit on thermistor or Time-out drain- Check filter for blockages then book a dishwasher repair if the problem persists.
- A04 – Unable to reach or sense temperature within 70 minutes – Book a dishwasher repair.
- A05 – Pressure switch has not been reset – Book a dishwasher repair.
- A07 – Open/Short circuit wash motor triac – Book a dishwasher repair.
- A08 – Open/Short circuit auxiliary wash motor triac – Book a dishwasher repair.
- A09 – Open/Short circuit with main wash traic – Book a dishwasher repair.
- A10 – Open/Short circuit fill valve traic – Book a dishwasher repair.
- A11 – Half load valve traic or alternating motor action – Book a dishwasher repair.
- A12 – Open circuit heater rely – Book a dishwasher repair.
- A13 – Open/Short circuit dispenser traic – Book a dishwasher repair.
- A14 – Drain hose too low causing syphoning. Check drain hose and re-adjust.
- H20 – Check tap and pressure of incoming water.
You can also buy spare parts for your dishwasher at the Hotpoint Dishwasher Spare Parts shop
Hotpoint Service – The only official home for Hotpoint Spares, Repairs and Accessories
Hotpoint Tumble Dryers
- F1 – The level of required dryness has not been reached within the time period. Check that the correct programme has been selected
- F2 – Thermistor or sensing circuit failure. Book a tumble dryer repair.
- F3 – Heater plate over temperature. Check the filter and vent hose for a possible blockage.
Fault codes for Hotpoint LCD Tumble Dryers
- F01 – Short circuit motor traic – Book a tumble dryer repair.
- F02 – Motor jammed or fan blocked – Book a tumble dryer repair.
- F03 – Front thermistor open/short circuit – Book a tumble dryer repair.
- F04 – No pump piloting – Book a tumble dryer repair.
- F05 – No feedback from the pump – Book a tumble dryer repair.
- F08 – Static heater relay with contact welded closed – Book a tumble dryer repair.
- F09 – Eeprom is not programmed or not functioning – Book a tumble dryer repair.
- F10 – Common of heater open or one shot open – Book a tumble dryer repair.
- F11 – No pump connection – Book a tumble dryer repair.
- F12 – Communication error between boards – Book a tumble dryer repair.
- F13 – Rear thermistor open/short circuit – Book a tumble dryer repair.
- F15 – Dynamic heater relay with contact welded closed – Book a tumble dryer repair.
- F-17 – Master relay welded closed – Book a tumble dryer repair.