Mosógép hibakód
IE hibakód – Nem vesz vizet (4 perc alatt a min. vagy 25 perc alatt a szükségeset)
UE hibakód – Ruha elrendezettlenség
OE hibakód – Nem ürít (8 perc alatt sem)
FE hibakód – (Overflow) túltöltés
PE hibakód – Vízszintszabályzó hiba
dE hibakód – Ajtókapcsoló nem zár
tE hibakód – Termisztor vagy fûtõbetét hiba
Mosogatógép hibakód
Error Code
Fault Description
IE
Inlet error. The fault indicates the level of water is not high enough after 10 mins of filling
OE
Drain error. The fault indicates the water is not draining out of the dishwasher
EI
Leak error. The water level in tub drops during use
FE
Fill error. The dishwasher has detected there is too much water in the unit and the drain pump is automatically switched on
TE
Temperature error. This indicates an issue with the thermistor of water temperature above 90C
HE
Heating error. This indicates the dishwasher could not heat the water or the water temperature reached 95C
Szárítógép hibakód
| No. | Error | Symptom | Cause |
|---|---|---|---|
| 1 | Humidity Sensor Failure | HS | The load is too small. The appliance is tilted. Laundry is gathered to one side. Non-distributable things are put into the drum. |
| 2 | Electric dryer power cord is not connected correctly, or house power supply is incorrect | PS or PF or nP | Not fully drained within 10 minutes. |
| 3 | The duct is about to 90%-95% blocked. („d90″ or d95” error code displayed 2 hours only) | d90, d95 | Water is overflowing. (water level frequency is over 21.3kHz). If FE is displayed, the drainpump will operate to drain the water automatically. |
| 4 | Door SW | dE | The THERMISTOR is out of order. |
| 5 | Wire connection (Black-White-Red) | PS | The connector (3-pin,male,white) in the MOTOR HARNESS is not connected to the connector(3-pin, female,white) of STATOR ASSEMLY. |
| 6 | Thermistor of stream generator | tE4 | EEPROM is out of order. Displayed only when the START/PAUSE button is first pressed in the Load Test Mode. |
| 7 | EE Prom operation is abnormal | EE | Machine is working, the power is supplied rapidly. |
| 8 | Water supply pump | E5 | If the washing machine detects too many suds, it displays the error code and adds Suds Reducig cycle. This adds about two hours to the cycle time. |
| 9 | Steam generator | ADD | Vibration sensor to break down |
| 10 | Drum outlet thermistor open/short | tE1 | The amount of liquid detergent in the detergent reservoir did not decrease. After putting the detergent into the detergent reservoir, it was lft for a long time and the detergent hardened. |
| 11 | Compressor discharge pipe thermistor temperature Open/short | tE2 | The amount of liquid detergent in the detergent reservoir did not decrease. |
| 12 | Restricted Motor (Restart- Not start motor- Not operation product-display „LE1”) | LE1 | The amount of fabric softener in the softener reservoir did not decrease. After putting the softener into the softer reservoir, it was left for along time and the fabric softener hardened |
| 13 | Detect low electric current | LE2 | The amount of fabric softener in the softener reservoir did not decrease. |
| 14 | When drainage pump doesn’t work well | OE | Ther washer was operated without completely closing the drawer. The drawer was opened during the washer operation |
| 15 | Compressor (restart – no drive product – sign „AE” error) | AE | The load is too small. The appliance is tilted. Laundry is gathered to one side. Non-distributable things are put into the drum. |
| 16 | If WiFi product is not registered (normal product) | nF | Correct water level (24.6kHz) is not reached within 8 minutes after water is supplied or it does not reach the preset water levelwithin 20 minut |
| 17 | Vibration Sensor Error | nE | Occurs when Vibration Sensor Communication is not working. Such as vibration sensor register setup error, removal, etc. |